The JA-80K control panel has 50 addresses for wireless devices and 2 hard 
wired
inputs. OASiS uses a reliable communication protocol at 868 MHz. Maximum
protection of wireless communication is guaranteed by the use of
floating code
and digital transmission technology. Installation into a building is very fast and
there are nearly no changes to the interior when using wireless detectors.
Programming can be easily done via a connected computer or remotely using the
relevant communicators. OASiS wireless detectors use 3V lithium batteries with a
3 year lifetime in common operation. The system checks batteries regularly and
signals replacement requirements.
Assigning detectors to sections A, B and C allows the individual security
requirements of different parts of buildings to be met. The control panel allows
you to either use two levels of partial setting (set section A, set sections AB or the
whole system – sections ABC) or to split the system into two independent
subsystems with a common section. The control panel is operated by keypads,
remote controls or remotely for example by mobile phone via a suitable
communicator. There is a built in RFID card reader in the keypad. Cards can be
used independently or their use can be qualified with the use of a code
for
increased security. The system can be operated with up to 50 access cards or
codes. Important information about operation of the system is registered in the
internal memory of the control panel, where the last 255 events are saved with
the date and time. With a suitable communicator the system can report selected
events in the form of an SMS to a mobile phone, send all details to an ARC, but
also inform an installer about the required service.
It also allows remote access to the system. It is possible to program the system,
set/unset, monitor the system or control devices in a building (heating, Venetian
blinds, lighting etc.) via mobile phone or internet. There are three optional
communicators supplied with the system – GSM, combined LAN/PSTN and voice
communicator.
The voice communicator can be combined with a GSM or LAN communicator.
In addition to control devices via its outputs, the control panel also offers many
other useful automation functions.
It optimises the regulation of heating and energy savings together with wireless
thermostats. The control panel sends all the important control commands via
radio, to wireless relay modules in range of the control
unit. The communication
range of wireless devices is hundreds of metres, depending on conditions. The
wide availability of wireless detectors, remote controls, sirens and automation
modules gives maximum freedom to
achieve the most suitable solution to
individual customer requests. The simple design of detectors allows installation of
the OASiS system into all interiors. The system was developed with an eye for
clean and fast installation (built-in mains-powered supply, optional communicator
modules, convenient programming by PC and Internet) and most of all for easy
and transparent operation and monitoring of the system by the customer. All the
texts used by OASiS for communication with its owner are editable to provide
information about events in a clear and understandable way.
CARACTERISTICI TEHNICE
No. of wireless zones 50
No. of hardwired zones 2 balanced
Communication band 868 MHz
Zone bypassing permanently or temporarily
No. of sections for partial armed mode 3 – A, B, C
No. of subsystems for a split system 2 with a common section
No. of access codes 50 (+ 1 service code)
No. of access cards 50
Events memory 255 events including date, time
Voltage 230 V, 50 Hz
Back up battery 12 V, 1.3 Ah or 2.6 Ah
Back up power supply output
12 V, 400 mA permanently, intermittently up to 1 A
External warning output relay max. 1 A/60 V
Internal warning output switching to GND, max. load 0.5 A
Programmable outputs PgX, PgY, max. 0.1 A, switching to GND
Dimensions 258 x 214 x 77 mm
Modul GSM Oasis
JA-80Y GSM/GPRS communicator
This module uses the GSM mobile phone network. It allows remote access to the system by mobile phone or via the Internet. It can also report events from the system to mobile phones and to alarm receiving centres (monitoring). It also provides a simulated telephone line (GSM gateway feature).
The communicator is designed to be installed within the control panel housing. When connected to a GSM network it allows the following:
- event reporting by SMS (to up to 8 telephone numbers)
- event reporting by phone call with an acoustic warning
- event reporting to an ARC (Automatic Receiving Centre – also known as a Central Monitoring Station) - up to 2 ARCs
- remote control and programming by phone (remotely authorizing a phone keypad or by SMS instructions)
- the remote control of appliances in the house by dialling in from an authorized number (free of charge with unanswered calls)
- remote control and programming via the Internet (www.GSMlink.cz)
- connecting a phone set = simulated tel. line = GSM gateway function (incl. CLIP protocol = caller ID and SMS transfer)
- listening-in and voice communication – via a connected SP-02 intercom
- connecting a PC to the Internet (GPRS modem feature)
Specifications
Power |
12V DC (from the control panel) |
Stand-by consumption |
about 35 mA (depends on the GSM signal) |
GSM band |
E-GSM / GPRS 900/1800MHz |
RF output power |
2 W for GSM900, 1 W for GSM1800 |
AUX output |
dry NC contact, max. 60 VDC / 100 mA |
Complies with |
EN 50131-1, EN 50136-2-1, as: ATS4, ATS 5 if CID protocol is used and the repeating period is set to zero (sequence 06a0) |
Security grade |
2 |
Operating environment |
(–10 to 40°C) class II |
Safety |
EN 60950-1 |
EMC |
ETSI EN 301489-1, ETSI EN 301489-7, EN 55022, EN 50130-4 |
Radio transmissions |
ETSI EN 301419-1 and EN 301511 |
CLIP protocol (caller ID + SMS) |
ETSI EN 300 089 V3.1.1(2000-12) |
Can be operated according to: |
ERC/DEC 98(20,21) |
The JA-80X voice module is used for the reporting of voice messages from the OASiS system via a PSTN line. It allows the recording of up to 6 voice messages which can be forwarded to up to 4 phone numbers. The communicator can also forward reports to ARCs in CID protocol. It is connected to the control panel bus by an RJ cable and it is possible to install it separately or in connection to a JA-80Y or JA-80V communicator. The communicator allows remote operating and programming of the system from a phone by DTMF commands.
The JA-80A wireless external siren is used for wireless communication with radio control panels of the JA-8x line. The siren is totally wireless, powered only by a lithium battery and there is no need for an external supply. Installation is therefore easily done and there is no need to find suitable supplies in the attic and a difficult power supply solution is avoided. The siren warns the surrounding area when a building is intruded. Handling which is not authorised such as tearing the siren off the wall, opening the cover etc is signalled to the system.
Communication with the control panel is two-way. The siren regularly checks its functions, battery status and checks transmissions to keep the radio connection.
Specifications
power |
lithium battery BAT-80 Jablotron |
battery life time |
calculated for max. 5 years |
communication band |
868 MHz, Oasis protocol |
communicating distance |
up to 300m (open area) |
siren |
piezo electric, 112 dB/1m |
max. duration of the audible alarm |
3 minutes |
max. duration of flashing during alarms |
30 minutes |
enclosure |
IP34D |
EN 50131-1 |
grade 2 |
dimensions |
230 x 158 x 75 mm |
working temperature |
-25 to +60°C |
operating environment |
class IV. |
can be operated according to ERC REC 70-03 |
|
The JA-80L is a mains-powered (230V AC) siren which sounds an alarm, and exit/entrance delays. If disconnected from the power while it sounds an alarm, it reports tampering to the system (i.e. intruder verification). Can also be used as a doorbell and as acoustic indication of detector triggering. Its indicator function is programmable. The siren can be enrolled to the control panel and also wireless detectors, RC controllers, wireless keypad inputs and the JA-80H door bell button can be enrolled to it to generate the desired sound.
It can be used as the following: An indoor alarm siren A wireless door bell A detector-triggered chime A sounder for entrance and exit delay beeps Thief verification The siren is mains-powered and communicates via OASIS wireless protocol. It can form part of an alarm system or be used as a stand-alone device.
When used as part of an alarm system, it sounds when an intruder alarm has been triggered and confirms the actual presence of an intruder in the building by sending a tamper signal when it gets unplugged. Installation shall only be undertaken by qualified technicians holding a training certificate issued by an authorized distributor.
Specifications
Power |
230V/50Hz, 1W |
Communication band |
868 MHz, Oasis protocol |
Communication range |
approx. 100 m (open area) |
Sounds (melodies) |
8 selectable for buttons and detectors, and an alarm siren sound 95 dB / 1 m |
Max. number of enrolled devices |
1x Oasis JA-80 control panel |
Safety class |
II according to EN60950 |
Operating environment |
general, indoor -10 to +40 °C |
Housing |
IP40 according to EN 60529 |
Mechanical immunity |
IK08 according to EN 50102 |
Operating conditions |
ERC REC 70-03 |
The JA-80L complies with ETSI EN 300220, ETS 300683, and EN 60950 |
|
SW-01
The RP-01 system can be connected to the PC via the SW-01 interface and software. In the system the interface is connected between the RS-485 bus and any free USB slot on the PC. Software called RFIDprog allow s you to setup, manage and control the system